Page Index Toggle Pages: 1 Send TopicPrint
I'll eventually learn... (Read 1974 times)
Hoot
KCA Forum Member
*
Offline


Krag Enthusiast!

Posts: 69
Location: Diversityville, Liberal-sota
Joined: Oct 11th, 2016
Gender: Male
I'll eventually learn...
Apr 14th, 2018 at 6:23pm
Print Post  
Sorry, I know this has been addressed but a couple of searches failed to bring it up. What I think I remember: the 1903 sling swivel screw (front, back, either?) can be used to mount the Redfield 'No-Drill' sight. Is this correct?

Thanks guys!
  
Back to top
 
IP Logged
 
butlersrangers
KCA Forum Member
*
Offline


Krag Enthusiast!

Posts: 6330
Location: Michigan Bi-Peninsular&Proud
Joined: Oct 7th, 2009
Re: I'll eventually learn...
Reply #1 - Apr 14th, 2018 at 7:17pm
Print Post  
Sort of:

1903 Springfield and Krag rifle rear barrel-band/swivel screws and Stacking-Swivel screws can be made to serve as side-plate screws to hold the 'no-drill' Redfield sight in place.

Sometimes, these swivel screws have had their tip 'mushroomed'. This has to be cleaned up or it is difficult to start the screw into the side-plate hole.

(This is no big deal because the screw has to be shortened a bit anyways).

Also, the diameter, of some of the screw shank, has to be reduced between where the threads end and the screw head. This is so the screw can enter the tapped receiver hole, deep enough, to clamp the Redfield base against the side-plate.

I have made such diameter adjustments by 'chucking' the screw-threads lightly in my Power Drill and holding a small File against the shank as it turns.

(Years ago, I bought some Replica swivel-screws that I could alter without feeling guilty. Now, I'm almost out of them and can't find more).

Photo contrasting screws. 2nd photo shows why rear barrel-band screw is better candidate.
  
Back to top
 
IP Logged
 
Hoot
KCA Forum Member
*
Offline


Krag Enthusiast!

Posts: 69
Location: Diversityville, Liberal-sota
Joined: Oct 11th, 2016
Gender: Male
Re: I'll eventually learn...
Reply #2 - Apr 15th, 2018 at 2:37pm
Print Post  
Thank you Sir!

Numrich has listed reproduction screws here => (You need to Login to view media files and links)

I have one on order and fingers are crossed.
  
Back to top
 
IP Logged
 
butlersrangers
KCA Forum Member
*
Offline


Krag Enthusiast!

Posts: 6330
Location: Michigan Bi-Peninsular&Proud
Joined: Oct 7th, 2009
Re: I'll eventually learn...
Reply #3 - Apr 15th, 2018 at 2:55pm
Print Post  
Here is a picture, (before & after), showing altered repro screw.

I do it by 'eyeball'. Works for me.
  
Back to top
 
IP Logged
 
Hoot
KCA Forum Member
*
Offline


Krag Enthusiast!

Posts: 69
Location: Diversityville, Liberal-sota
Joined: Oct 11th, 2016
Gender: Male
Re: I'll eventually learn...
Reply #4 - Apr 16th, 2018 at 2:13pm
Print Post  
Nicely done!

We'll see if mine turns out as neat.

Thanks again!
  
Back to top
 
IP Logged
 
carbon outlaw
KCA Forum Member
*
Offline


carbon outlaw

Posts: 209
Joined: Jul 4th, 2014
Re: I'll eventually learn...
Reply #5 - Apr 19th, 2018 at 11:19pm
Print Post  
Hi from Carbon Outlaw .... I know of your delema .. I went to home depot to find screws and came up short ... I spent a lot of time development a way to make screws for the redfield no drill sights ... 70 kt sight and 102 sight ... I'm not sure but I think there is a way to look at my posts I did in the past years it explain a way to make your own screws ... Thanks Carbon Outlaw ...
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint