Krag Collectors Association Forum Archive - System Information

(UTC)

Krag Collectors Association Forum Archive › Firearms › U.S. Military Krags › Questionable front sight

(Moderators: Ned Butts, Tom Butts, KCA Forum Admin)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Questionable front sight (Read 3313 times)

butlersrangers KCA Forum Member Offline Krag Enthusiast! Posts: 6330 Location: Michigan Bi-Peninsular&Proud Joined: Oct 7^th, 2009	Questionable front sight Jul 21^st, 2018 at 5:32pm	Print Post
	Is it just me? On another forum a while back, photos were posted of a very proper looking U.S. model 1899 carbine. This was the final picture posted. It shows the front-sight base, with the carbine front-sight protector removed. (The new owner described the barrel "as being a tad over 22 inches", but, I am not sure he measured it properly)? Something looks wrong to me. IMHO - This may be a real carbine barrel, but, I think an original front-sight base has been "re-attached". It appears to me, there is the remains of a base brazed into the Springfield Armory barrel dovetail. It looks like a replacement base brazed on top of that. Head Scratcher!


	IP Logged

Parashooter KCA Forum Member Offline Kragmudgeon Posts: 514 Location: Connecticut Joined: Feb 4^th, 2010	Re: Questionable front sight Reply #1 - Jul 21^st, 2018 at 6:46pm	Print Post
	Looks original to me, but all the dirt, dust and debris obscuring the joint makes it hard to tell - as does shadow on near side of stud. Why on earth do folks have to play with sight protectors - on, off, on, off . . .?


	IP Logged

Whig KCA Official Member Offline Krag Enthusiast! Posts: 1324 Location: Balt MD Joined: Sep 24^th, 2016 Gender:	Re: Questionable front sight Reply #2 - Jul 22^nd, 2018 at 5:39pm	Print Post
	Could an 03 band sight had been mounted and the original sight reattached by a skilled welder?


	IP Logged

butlersrangers KCA Forum Member Offline Krag Enthusiast! Posts: 6330 Location: Michigan Bi-Peninsular&Proud Joined: Oct 7^th, 2009	Re: Questionable front sight Reply #3 - Jul 22^nd, 2018 at 7:05pm	Print Post
	Parashooter has a keen eye and is usually correct. Likely, this front-sight just needs a good cleaning with a toothbrush and some Hoppe's to remove fuzz and gunk. The camera lens has probably made a straight machined 'line' look a bit curved.


	IP Logged

madsenshooter KCA Forum Member Offline Krag Enthusiast! Posts: 1079 Joined: Sep 10^th, 2009	Re: Questionable front sight Reply #4 - Jul 25^th, 2018 at 11:01pm	Print Post
	What I can make out of the dovetail at the front says original to me.


	IP Logged

butlersrangers KCA Forum Member Offline Krag Enthusiast! Posts: 6330 Location: Michigan Bi-Peninsular&Proud Joined: Oct 7^th, 2009	Re: Questionable front sight Reply #5 - Jul 26^th, 2018 at 1:28am	Print Post
	I was suspicious of what appeared to be a high and curving 'ridge'. Upon reflection and consideration of Parashooter's and your opinion, I now think it an illusion, caused by hardened cosmoline, debris, and 'lens curvature'. Sometimes I shoot my mouth off too much ... think I'll take some pills for it!


	IP Logged

Mark21 KCA Forum Member Offline Krag Enthusiast! Posts: 17 Location: Florida Joined: Jan 5^th, 2018 Gender:	Re: Questionable front sight Reply #6 - Jul 27^th, 2018 at 4:21pm	Print Post
	The sight looks right. The ware pattern on the side could be from a sight cover. The wear area only goes part way around the barrel. Would like to know if the blade is marked with a C.


	IP Logged

Doco Overboard KCA Forum Member Offline Krag Enthusiast! Posts: 57 Location: Eastern Shore of MD Joined: Nov 21^st, 2017 Gender:	Re: Questionable front sight Reply #7 - Jul 28^th, 2018 at 3:43pm	Print Post
	The width of the slot for the site blade was slightly wider on a replacement base I used. Maybe it was just the one I had received but I had to form my own blade. It also had a more robust exterior dimension in the radius at the front and rear of the post and was slightly wider. My amateur opinion is that is a replacement base from what I can observe from the images. It's an opinion only, hope I'm wrong.


	IP Logged

butlersrangers KCA Forum Member Offline Krag Enthusiast! Posts: 6330 Location: Michigan Bi-Peninsular&Proud Joined: Oct 7^th, 2009	Re: Questionable front sight Reply #8 - Jul 28^th, 2018 at 4:40pm	Print Post
	'Doco' - A little bit of black 'gasket-seal' nicely firms up a loose Krag front-sight blade in a sloppy base. It eliminates wobble and can always be 'un-done'. I rather regret starting this thread. Sight is probably correct. Just looks wrong because of dried goop, lint, scratched finish, and photo distortion.


	IP Logged

Mark_Daiute KCA Forum Member KCA Official Member Offline I love YaBB 1G - SP1! Posts: 242 Location: Newcastle Maine USA Joined: Jul 11^th, 2003 Gender:	Re: Questionable front sight Reply #9 - Jul 29^th, 2018 at 12:38pm	Print Post
	I would like to see this scrubed hard with oooo steel wool. If the joint looks invisible/nearly invisible, well then, its good but looking at the photo as it appears here I would've considered it bogus, but hey, that's me.


	IP Logged

butlersrangers KCA Forum Member Offline Krag Enthusiast! Posts: 6330 Location: Michigan Bi-Peninsular&Proud Joined: Oct 7^th, 2009	Re: Questionable front sight Reply #10 - Jul 29^th, 2018 at 12:58pm	Print Post
	A toothbrush and some Hoppe's would probably clean up the sight, in question, nicely. (I now think it's correct, but, greasy & dusty, which made it suspect). Attached are photos of a Krag model 1898 rifle and model 1899 carbine front-sights to show rather typical appearance of sight base attachment. IMHO - With short Krag barrels, (22" & 26"), this is the first place to look for 'mischief' and fakery.
	« Last Edit: Aug 3^rd, 2018 at 3:00pm by butlersrangers »

	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›